Re: [Discuss-gnuradio] gnuradio build from script fails

Hi Organ,
This all sounds like you still have the horribly outdated version of UHD installed that Ubuntu 14.04 has. Make sure to
sudo apt-get remove uhd libuhd\* uhd-host

And run build-gnuradio again.

Best regards,
Marcus

Am 27. November 2015 04:36:17 MEZ, schrieb "Orhan Öçal" <orhanocal@gmail.com>:

Hello,

I have been trying to have GNURADIO and USRP B200 work on a Ubuntu 14.04.3

I have first tried the call `sudo apt-get install gnuradio`. This installs GNURADIO fine. However, the drivers for B200 is not installed unfortunately, hence the machine cannot see my device.

So instead I downloaded the driver binaries after updating the apt-get package manager through the way written on ETTUS research's website http://files.ettus.com/manual/page_install.html#install_linux_pkgmgr This solved the problem with connecting to USRP B200. However, it uninstalled gnuradio as expected since it depends on the UHD library. Then I installed gnuradio by `apt-get install gnuradio`. However, this gives a segmentation fault when I try running gnuradio. This link https://www.ruby-forum.com/topic/4837808 mentions about such a problem due to `libboost`, I believe I have the same problem.

So instead I tried building GNURADIO and UHD through the installation script as `wget http://www.sbrac.org/files/build-gnuradio && chmod a+x ./build-gnuradio && ./build-gnuradio`. However, with this I get the following error:

##############################

[ 87%] Building CXX object gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o

/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx: In function 'void init_uhd_swig()':

/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47037:91: error: 'ATR_REG_IDLE' is not a member of 'uhd::usrp::dboard_iface'

   SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_IDLE",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_IDLE)));

                                                                                           ^

/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47038:94: error: 'ATR_REG_TX_ONLY' is not a member of 'uhd::usrp::dboard_iface'

   SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_TX_ONLY",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_TX_ONLY)));

                                                                                              ^

/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47039:94: error: 'ATR_REG_RX_ONLY' is not a member of 'uhd::usrp::dboard_iface'

   SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_RX_ONLY",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_RX_ONLY)));

                                                                                              ^

/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47040:98: error: 'ATR_REG_FULL_DUPLEX' is not a member of 'uhd::usrp::dboard_iface'

   SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_FULL_DUPLEX",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_FULL_DUPLEX)));

                                                                                                  ^

make[2]: *** [gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o] Error 1

make[1]: *** [gr-uhd/swig/CMakeFiles/_uhd_swig.dir/all] Error 2

make: *** [all] Error 2

make failed

Exiting Gnu Radio build/install

​​##############################

The script builds ​UHD itself, I could not think of how to approach this problem. Would you have any hints as to how to proceed?

Oh, and, happy thanksgiving!

​Orhan​

Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio

--
Sent from my Android device with K-9 Mail. Please excuse my brevity.